Wire the LCD RKP as shown in the wiring section of this manual. Replace the .. The Eurosec CP8 LCD has two log modes. These are: a). gardtec eurosec cpx installation manual · Home · Blog · About · Press · Contact · Home · Blog · About · Press · Contact. Powered by カスタマイズ可能なテンプレート . A range of alarm system user guides and manuals for owners and clients. Accenta 6 · Euro 46 User Manual · Euro Mini User Guide · Eurosec CP7/CP8 LED .

Author: Zulubei JoJobei
Country: Vietnam
Language: English (Spanish)
Genre: Technology
Published (Last): 25 June 2006
Pages: 92
PDF File Size: 10.42 Mb
ePub File Size: 17.95 Mb
ISBN: 975-4-38376-659-3
Downloads: 25904
Price: Free* [*Free Regsitration Required]
Uploader: Dajinn

Follow the euroeec for programming User Codes onto your system up to the point when you would enter the User Code. Wait until the exit tone finishes before leaving. Vo-Comm messages may be sent to standard land line telephones or mobile telephones. Pressing 7 will take you to back to the last event of the previous day.

Press Yes Year is ok? Chime is Off ok? A rising tone will be heard that indicates that the call has been acknowledged.

Alarm System User Guides And Manuals

I mean do some kind of connection or make any changes through the keypad? Biased To set the system with a biased keyswitch, insert the key and turn it then return the key instaolation the original position and remove. It is important that your security system is serviced on a regular basis on order that it continues to comply with the legislation.

Community Forum Software by IP. I am using only 6 zone, should I leave the 2 zone as there are on the panel or do I need to do anything installatoon them?


At this point present you Tag to inztallation Proximity Reader and a code will be entered for you. Entering will delete an existing code Note: The display will clear once the power is restored.

Before Vo-Comm can work several options will need to be programmed.

Posted 05 January – The display will show: The User Code levels available and the functions available for the levels are: If you do not installarion the call or hear the rising tone the Vo-Comm will repeat the message several times and then go on to dial the remaining telephone numbers until the call is acknowledged.

All Zones ON 2 Enter the code again to abort the setting 3 The system is now reset 15 Time will count down Or If a eurosev level of code is required one of the following displays will be shown: To program a Control Code level. Press 0 to escape. The term Open relates to the system being Unset. This determines if using this user code to Set or Unset the system will trigger the Vo-Comm for more details on Vo-Comm please refer to the Vo-Comm section.

Press No until the setting you require is displayed Yes or No. Because the G-Tag uses Proximity Technology there are no batteries to change in the unit, it is small enough to be carried on the users key ring and one Tag may be used on multiple security systems and some door entry systems.

Follow the normal instructions for programming codes. Follow the instructions from step 3 above. At the end of the message you will hear a single tone, at this point press a key on your telephone keypad twice. The Vo-Comm will need to be programmed in order for this option to work please refer to the Vo-Comm section in this manual.


Posted 31 December – If the system was Set a full alarm will be generated. If you euurosec a blank space press YES while the ‘-‘ is displayed 14 As you press YES for the ninth character or if you have jumped from step 9 the display will change to: Zone remove is only effective for the one set.

Eurosec CP8 Manuals

Press NO, the display will show: In the event of any errors the display will show: Control Allows an output that has been pre-programmed by the installation company to be operated. If this option has been invoked by your installation company the Set or Unset Status will only be displayed for ten seconds when the system is Set or Unset.

Then choose Can or Cant Unset dependant on your requirements. G-Tag Fob Legislation contained within Mamual does not allow for the transmission of confirmed alarm signals once the entry time has started if the user of the security system is using a manual code entered into the intsallation. Read Log 01 JAN